Change the value for strRemoteComputer with your own Remote Computer name to Read Registry Value. Once we have done that, we can check it, and then use example 2 see below to delete this registry entry. Beside that, I personally prefer to use Join and Split wherever I can, rather than loops. This example sets the string value. You do not need to create two sets of keys for one process.
Before you even think about using. I had a little time and tested. Change the value for strKeyPath and strValueName with your own registry path and name. Save the file with a. If you just write it to the registry on each system the key will be visible to all processes on either system. It may not 'be used for commercial purposes with out the expressed written consent 'of NateRice.
The best way to distribute registry setting is by exporting the part of a registry where this setting is active to a. Then read from the array and write it, appending to the registry - I can see all the entries from the text file using wscript. I suspect that the process will see the key unless it is run in an isokated 32 bit process. I added the error's to my event log. Change the value for strKeyPath and strValueName with your own registry path and name.
Close Though I'm sure the concept is valid, I don't have an easy way to test this, so I can't absolutely guarantee there isn't a syntax or other logic problem here. For example is there a group policy to achieve your aim? I have viewed the contents of NewstrValue at different points in the script and it looks like it is always holding all of the existing values so I am not sure why it is only writing the last read. When I run it locally on my machine it works fine and the registry key gets added as intended. Jerry Lees Profile: On occasion when administering a group of systems you need to preform certain tasks depending on if something is installed or a particular setting is a certain value and the only way to determine if a system needs attention is to look in the registry. Additionally, remember that you reference the path all the way to the data you want including the value name, if you are specifying a value.
Change the value for strKeyPath and strValueName with your own registry path and name. I tried to ways shown below. The parameter Subkey is not case-sensitive. To use it, you'll need to get the key you want to change from the registry. It contains settings for low-level operating system components and for applications running on the platform that have opted to use the registry. Do we need to create a Script Center key, then create a My Registry Keys key, and then, finally, create a Test Key key? Have recently had a problem when i had to read and write 64-bit registers.
Keys may contain values or further keys aka subkey. The system can do this for you. RegWrite is to adjust data. The registry contains two basic elements: keys and values. My environment is Windows 2008 R2. Close You're failing to collect all of the array elements together in your loop. November 16th, 2006 Hey, Scripting Guy! If the test is to be done only on a local machine strComputer always equal to dot , then this Wscript.
Our next chore is to assign the registry path for the new registry key. How can I create a new registry key? Double-click the vbscript file or Run this file from command window to get Multi-String Registry value using vbscript. Thanks again Do until newKeyFile. Is it possible to achieve your aim with a. What happens is that it adds only the last Value existing values in NewstrValue then appends the new ones. RegRead you can read only the very end value, in this case, 1. Manipulating the registry is one of the most common tasks a Windows system administrator runs into.
There are a number of commands that we could use to achieve our goal. RegWrite could create it, all you have to do is specify the data type. Copied from my full script pasted earlier - these lines read from a file and puts it into array that i can still read line by line. To take it a stage further. I hope not, but please realize I can't offer a warranty. RegWrite is the most important and versatile method. Plus, you can't add additional array elements with the Array function.
Reg file into your registry. In practical terms, what I mean is if a value called PaintDesktopVersion did not exist, then. I can't get it to work. If I use the On Error Resume Next I'm not sure if it corrupts the test results of the 2nd and 3rd registry keys. Doing this with a script means having to pass additional layers of security to make sure this isn't a malicious script. So, lets look at the code. And last, you shouldn't need the pushd, and popd commands and I would not do the Set-Location.
When reading the registry from a Web application, the current user depends on the authentication and impersonation implemented in the Web application. On this page, we will consider just three methods for modifying the registry,. Thank goodness for basketball, huh? Even normal users should be able to do this. RegRead What you could do is read a value from the registry, then depending on the result, modify values in another area of the registry. When you put data in the registry value, the data is available to the other process. The hierarchy of registry keys can only be accessed from a known root key handle.